INSIST on ONLY High Quality 
Genuine Original Weber Carburetors
manufactured in Spain/Italy for the last 30+ years
(They should be Stamped Made in Spain)
(Don't be fooled by Cheap Copy's Call if your not sure)
253-833-4106

All Weber has a 90 Day Warranty

IMB Series Weber Carburetors

The IMB  1 barrel downdraft carburetor. It's easily tailored to small engine setups to  (Fiat cars ,generators) 
Bolt pattern Stud holes 6.5mm  spacing 44mm
(Made in Spain)

ICT Series Weber Carburetors

The ICT and ICH Series 1 barrel downdraft carburetor. It's easily tailored to most OEM engine setups to produce good gas mileage and good performance .(Other uses include forklifts , snowmobiles and generators) 
Bolt pattern is slotted 2 inch inside of bolts ,3 inch outside of bolts
(Made in Spain)

Jet kits and parts

32/36 DGV Series Weber Carburetors

Genuine Weber Carburetors
Any search for the ideal 2-barrel, progressive down-draft carburetor would surely end with the DGV Series. look no further for versatility, wide adaptability, easy installation, low initial cost, trouble-free maintance, excellent drivability, increased fuel economy and improved performance. Designed for 4-6 cyl engines,  the DGV Series carbs feature diaphragm type accelerator pump circuits and models with manual, water or electric choke actuation. The DGV also has a power valve circuit to facilitate low vacuum running conditions. (Made in Spain)

** DFEV = DFAV with electric choke   ** DGEV= DGAV with electric choke
Jet kits and parts

38  Series Weber Carburetors

Greater improvements in throttle response at a slight penalty in fuel economy can be achieved by using the 38 DGAS  38 DGES synchronous-opening model. Both can be used as a high performance alternative to most any DGV applications
 4 to 8 cylinder engine setups (Made in Spain)

** DGES = DGAS with electric choke
Jet kits and parts

48 IDA Weber Carburetors

It is unsurpassed for full-race use, yet its infinite tunabilty by way of interchangeable calibrated parts allows it to be tailored to suit many engine applications. (Made in Spain)

IDF Series Weber Carburetors

IF you find it Cheaper We will try to Beat It
With its central float chambers, full calibration capabilities, compact alloy body and wide variety of available sizes, the IDF Series has been and continues to be the winning choice for a synchronous, 2 barrel, downdraft carburetor. The IDF features diaphragm type accelerator pump circuits and ball bearing throttle shafts. When used with an adapter, the IDF will replace the Solex 40 PII carburetors used on many Porsches. The IDF is ideal for use on most opposed-cylinder engines, or on engines where the intake ports are nearly vertical. Offering relative low cost for performance gained, the IDF is hard to beat. (Made in Spain)

Jet kits and parts

DCOE / DCO Series Weber Carburetors

With a Grand Prix Racing heritage, the venerable DCOE is Weber's premier Carburetor, and still the standard by which all other carburetors are measured. It is unsurpassed for full-race use, yet its infinite tune ability by way of interchangeable calibrated parts allows it to be tailored to suit any engine and application. Hardly enough can be said about the DCOE. Its features include: ball bearing throttle shafts, piston type accelerators pump circuits, a wide variety of throttle bore sizes.. and, of course, the excellence that is Weber. (Made in Spain)

Jet kits and parts

Jet kits and parts

The DCNF is a synchronous-opening, 2-barrel, down-draft carburetor, Despite its compact size, it is capable of high rates of flow. Interchangeable venturi and accelerator pump cams add to the versatility of these units, which are particularly useful in applications where engine compartment limitations dictate a compact-size carburetor. Other features include diaphragm type accelerator pump circuits, separate starting circuits and ball bearing throttle shafts. The DCNF has been used extensively on Ferraris, and are well-suited to multiple-unit applications.

Jet kits and parts

IDA 3c Weber Carburetors  These NEW Weber 3 Barrels are cast and machined using 100% new tooling made from the original Italian Weber blueprints. Manufactured in Spain, at the Genuine Weber manufacturing facility, we use the very latest production techniques to ensure the finest quality and attention to detail.

As part of our special relationship with Weber, we conduct a series of tests and adjustments on every Weber we sell. We only use factory Weber equipment to ensure each carburetor is working correctly, matched for multi-carb applications, as well as to ease installation and minimize final tuning adjustments.

Jet kits and parts